Indian
Suppliers
Suppliers
Multitech Engineers
Category : Industrial Supplies
"Multitech Engineers" Three pass heating systems essentially comprises of a fully automatic packaged Oil/Gas THERMIC FLUID HEATER. As a result thermic fluid can be heated upto 300°C at near atmospheric pressure, with efficiency as high as 87% on NCV of Oil/Gas fuel.
HEAT EXCHANGEER:
Heatex Oil/Gas Fired Thermic Fluid Heater is horizontal-cylindrical design. The Burner assembly is designed for easy adjustment, cleaning & maintenance of diffuser plate, nozzle electrode etc. For long term cleaning of coil, it is quite convenient to take out the oil as it is horizontally designed . It is a three pass to coil forced draft Thermic Fluid Heater.
Heatex Thermic Fluid has two shells. One is inner shell in which coil is fitted. inner shell is fitter in outer shell. Aluminium sheet is provided between outer shell & inner shell so heat can not go on the outside surface. This will maintain the general temperature inside the oil of Coil. Both sells are made from M.s Plate.
BURNER:
This is of the important part of our Oil/Gas Fired thermic Fluid Heater. It is specially designed and manufactured by us. It helps to give combustion efficiency around 85% to 88%. It consists of Oil pre-heater, a high pressure gear Pump, burner gun, electrode & nozzle. The burner flame is a hollow cone type which gives maximum heat transfer in the radiation zone.
AUTOMATION:
The heater is fully automatic in operation. The following instruents are provided for precise control of the operations.
DEAERATOR CUM EXPANSION TANK:
The conbined deaerator cum expansion tank is so designed as to take care of the expansion of thermic fluid and also to drive away the gases orentrapped air. The Temp. of thermic fluid inside the tank is not more that 90º C to prevent oxidation of oil
HEAT EXCHANGER COIL:
It is made from B.S. 3059 boiler quality tubes. Two pipes are welded very precisely. Besides, the coil is hydraulically tested at a pressure of 300 PSI.
APPLICATION :
Heatex Thermic Fluid Heater is applied in industries like Textile, POY Plants, Chemicals, Rice Mills, Leather, Rubber, Plywood, Dehydrations, Packaging, Pharmaceuticals and oil refineries, etc.
Technical Specification
|
S. No. |
Description |
UNITS |
ST-100 |
ST-200 |
ST-400 |
ST-600 |
ST-1000 |
ST-1500 |
|
1 |
HEAT OUTPUT |
Kcal/Hr |
1,00,000 |
2,00,000 |
4,00,000 |
6,00,000 |
10,00,000 |
15,00,000 |
|
2 |
MAX. OPERATING EMP. |
O C |
300 |
300 |
300 |
300 |
300 |
300 |
|
3 |
THERMIC FLUID |
- |
THERMINOL 66 OR EQUIVALENT |
|||||
|
4 |
THERMIC FLUD FLOW |
M³/Hr |
7 |
10 |
30 |
40 |
70 |
110 |
|
5 |
BURNER TYPE |
- |
VERTICAL, DOWN FIRING PRESSURE JET ATOMISING FORCED DRAUGHT. |
|||||
|
6 |
BURNER CONTROL |
|
ON – OFF (OPTIONAL – HIGH/LOW OR MODULATING) |
|||||
|
7 |
APPROX. THERMAL EFFICIENCY |
% |
87 + 2 ON NCV |
|||||
|
8 |
APPROX. FUEL LDO : CONSUMPTION FO: |
Kg/Hr |
11.4 - |
22.6 24 |
45 47.6 |
67.7 71.6 |
113 119 |
170 179 |
|
9 |
ELECTRIC SUPPLY |
- |
AC 415V + 6%, 50Hz + 3%, 3 PHASE, 4 WIRE SYSTEM |
|
||||
|
10 |
CONNECTED LOAD |
|
||||||
|
10.1 |
T.F. PUMP MOTOR |
Hp/Kw |
5/3.75 |
7.5/5.5 |
12.5/9.4 |
15/11.3 |
20/15 |
30/22.5 |
|
10.2 |
FUEL PUMP MOTOR |
“ |
---------------0.5 / 0.37 ----------------------------- |
1/0.75 |
1/0.75 |
|||
|
10.3 |
BLOWER MOTOR |
“ |
1/0.75 |
2/1.5 |
2/1.5 |
3/2.25 |
5/3.75 |
7.5/5.63 |
|
10.4 |
CONTROL |
“ |
0.5/0.37 |
|||||
|
10.5 |
| |||||||